Skip navigation

SFP2 REVO surface finish probe

SFP2 surface finish (roughness) measurement system with automatic probe and module configuration changing via RCP TC-3 and RCP2 REVO-2 change ports mounted on MSR / MSR2 module change rack

  • Knowledgebase top level image - REVO-2 and SFP2SFP2 is used in conjunction with skidded modules to access bores as small as 5 mm (0.2 in) diameter
  • Output: Ra, RMS and raw data are returned from UCCserver to the metrology application client software using the I++ DME protocol (raw data can subsequently be presented to specialist surface analysis software packages for further detailed reporting)
  • Sensor calibration involves measuring the surface finish of the calibration artefact (SFA) mounted on the MRS2 rack
  • The calibration software automatically adjusts the probe output in accordance with the calibrate value of the artefact
  • The SFP2 includes an integral motorised C-axis that enables surface finish measurements to be made at all required orientations around a part

Dimensions

SFP2

SFP2 - dimensions

Change ports

RCP TC-3 and RCP2 - dimensions

NOTE: Dimensions in mm (in). Overall dimensions are to the kinematic planes.

Specifications

SFP2 probe



C-axis positioning accuracy

± 0.25°

C-axis rotation speed

Up to 90°/sec

Rotational capability

A-axis (from REVO-2): +120° / -110°

B-axis (from REVO-2): Infinite positioning

C-axis: ± 180˚

Mounting (probe and holder)

Magnetised coupling


Specification


Probe head

REVO-2 only

Change rack

MRS2 recommended for full capability

Software compatibility

UCCsuite 5.2 onwards

MODUS 1.8 onwards

Weight

SFP2 probe: 330 g

SFH1 holder: 33 g

SFM-A1 module: 12 g

SFM-A2 module: 12 g

Operating temperature range

+10 ˚C to +40 ˚C

Storage temperature range

-25 ˚C to +70 ˚C

Operating humidity

0% to 80% (non-condensing)

Calibration and verification artefacts

SFA1: 3.0 μm Ra sinusoid

SFA2: 0.5 μm Ra sinusoid

SFA3: 0.4 μm Ra sawtooth

TFP: Uses LF TP20 module; PICS interface to SPA3 amplifier

Outputs

MODUS basic: Ra, Rms(Rq)

MODUS standard surface texture: Rt, R3z, Rz, Rz1max, RzDIN, RzJIS, Rseg Rp, Rv Rpm, Rvm, Rc, Rsm

MODUS advanced surface texture: Rk, Rpk, Rvk, Rmr, Rmr1, Rmr2, Rpq, Rvq, Rmq, Rvoid, Rvdd, Rvddl, Rcvx, Rcvxl

Sampling rate

4 kHz


SFP2 probe change system

The REVO-2 probe change system is designed to allow automatic REVO-2 probe and accessory changing on a CMM. For optimum metrology, SFP2 probes and holder / module configurations should be changed automatically using REVO-2 change ports (RCP TC-3 and RCP2). These ports are mounted on the modular rack system (MRS or MRS2).

5-axis change systems - SFP2 with SFH-2, RCP TC-3 and RCP2

Part number

REVO SFP2 kits

SFP2 combi kit #1 (A1 and A2 modules, single artefact)

A-5764-0001

SFP2 combi kit #2 (single artefact, no modules)

A-5764-0002

SFP2 combi kit #3 (A1 and A2 modules, triple artefact)

A-5764-0003

SFP2 combi kit #4 (triple artefact, no modules)

A-5764-0004

Single artefact kit (SFA1 and single artefact holding kit)

A-5764-0072

Triple artefact kit (SFA1, 2, 3 and triple artefact holding kit)

A-5764-0073

SFP2 probe and modules

SFM-A1 2 µm general purpose straight module (type A skid)

A1-D-02C90D

SFM-A1 5 µm general purpose straight module (type A skid)

A1-D-05C90D

SFM-A2 2 µm general purpose cranked module (type A skid)

A2-D-02C90D

SFM-A2 5 µm general purpose cranked module (type A skid)

A2-D-05C90D

SFM-B1 2 µm straight module with smaller skid for short lands (type B skid)

B1-D-02C90D

SFM-B1 5 µm straight module with smaller skid for short lands (type B skid)

B1-D-05C90D

SFM-B2 2 µm cranked module with smaller skid for short lands (type B skid)

B2-D-02C90D

SFM-B2 5 µm cranked module with smaller skid for short lands (type B skid)

B2-D-05C90D

SFM-B3 5 µm 90° module with smaller skid for pockets and grooves (type B skid)

B3-D-05C90D

SFM-B4 5 µm cranked module with smaller skid for reach into confined areas (type B skid)

B4-D-05C90D

SFM-B5 5 µm cranked module with smaller skid for reach into undercuts and grooves (type B skid)

B5-D-05C90D

SFM-C3 2 µm straight module for small bores (type C skid)

C3-D-02C90D

SFM-C3 5 µm straight module for small bores (type C skid)

C3-D-05C90D

SFM-D1 2 µm 90° module for extra reach (type D skid)

D1-D-02C90D

SFM-D1 5 µm 90° module for extra reach (type D skid)

D1-D-05C90D

SFM-E1 2 µm long straight module with 2-part skid (type E skid)

E1-D-02C90D

SFM-E1 5 µm long straight module with 2-part skid (type E skid)

E1-D-05C90D

SFM-E2 5 µm long straight module with 2-part skid (type E skid)

E2-D-05C90D

SFM-G1 Grooved engine bores prepared for PTWA coating (type G skid)

G1-D-10C30C

SFM-H1 automatic transmission valve bodies, minimum feature access (mm): Ø9 × 122 (max. depth) (type H skid)

H1-D-02C90D

SFM-H1 5 µm automatic transmission valve bodies, minimum feature access (mm): 9 122 (max. depth) (type H skid)

H1-D-05C90D

Accessories

SFH-1 surface finish module holder

A-5764-0080

SFH-2 surface finish module holder

A-5764-0081

SFA1 3.0 SIN artefact (SFA1 plate with UKAS certificate)

A-5764-0060

SFA2 0.5 SIN artefact (SFA2 plate with UKAS certificate)

A-5764-0061

SFA3 0.4 ST artefact (SFA3 plate with UKAS certificate)

A-5764-0062

OFA optical flat artefact (* special product)

A-5764-3142

Single artefact holder mounting kit. Contains: SFAH-1 single plate holder, rack adaptor, leg adaptor, fixings for all options, tools

A-5764-0070

Triple artefact holder mounting kit. Contains: SFAH-2 triple plate holder, rack adaptor, leg adaptor, fixings for all options, tools

A-5764-0071

TFP tip find probe kit (including TP20 LF mod, stylus, PL24 cable)

A-5764-0063

MST module setting tool

A-5764-0091

System storage box

A-5764-0090

NOTE: Please visit the REVO system for a full list of REVO-2 system and associated product part numbers.